- Building Material
- Compressed Concrete Slab / Concrete Grating
- HYRIB MESH
- Kitchen equipment
- Polyethylene Membrane Plastic Sheet Wholesaler
- PP Corrugated Board Wholesaler
- SAFETY PRODUCT
- Solar LED Flood Light / Street Light / Rechargeable
- Others
SIGNATURE BUILDING MATERIAL SDN BHD
No.20-G, 20-1, 20-2, Jalan Set 3/1, Setia Eco Templer, 48000 Rawang, Selangor, Malaysia.
+6016-358 6663
FOSROC NITOMORTAR UA (6 LITRE SET) Two Part Epoxy Resin Mortar for Wet and Underwater applications
| Previous | 7 / 12 | Next |
Nitomortar mortars are two pack epoxy resin mortars. Each part is a different colour to provide visual
confirmation of adequate mixing on site. Nitomortar cures chemically and therefore does not require the presence of water, solvent or oxygen.
Nitomortar products have high comprehensive strengths, cure with negligible shrinkage and are resistant to chemical and physical attack. After 48 hours at 20 derajat C Nitomortar compounds will have achieved between 60 to 70% of their final compressive strength.
Uses
- General Purpose Applications
Nitomortar GP is a versatile low slump material used for general repair work. Typical applications include patching spalled or honeycombed vertical surfaces, protecting exposed reinforcement, reinstating damaged arrises and repairing damaged precast concrete building units.
- Bedding Applications
Nitomortar BC is designed for bedding applications and can be trowelled to a fine accurate surface. Applications include bedding concrete kerbs to concrete, bedding bridge bearing pads and mounting heavy plant and equipment.
- Underwater Application
Nitomortar UA is formulated for use in exceptionally wet conditions and underwater applications. Nitomortar UA is recommended for reinstating structures exposed to the heavy battery of the sea (e.g.: sea walls) for repairing submerged steelwork or concrete (particularly exposed reinforcement) and for fixing slip bricks, tiles and tiles pointings.
Advantages
· High compressive strengths
· Fast cure
· No shrinkage on curing
· Excellent resistance to chemical physical attack
Coverage
Nitomortar : 1 ltr/m2 per mm thick
Properties
Setting time : 30 to 45 minutes at 20 C
Cure time Initial cure : 24 hrs. at 20 C
Final cure : 7 days at 20 C
Shrinkage on cure : None
Water immersion : Nitomortar UA may be applied underwater.
Compressive strength: After 1 week at 25-27 C
Nitomortar UA : 70 N/mm²
Flexural strength After 1 week at 25-27 C
Nitomortar UA : 35 N/mm²
Tensile strength : After 1 week at 25-27 C
Nitomortar UA : 12 N/mm²
confirmation of adequate mixing on site. Nitomortar cures chemically and therefore does not require the presence of water, solvent or oxygen.
Nitomortar products have high comprehensive strengths, cure with negligible shrinkage and are resistant to chemical and physical attack. After 48 hours at 20 derajat C Nitomortar compounds will have achieved between 60 to 70% of their final compressive strength.
Uses
- General Purpose Applications
Nitomortar GP is a versatile low slump material used for general repair work. Typical applications include patching spalled or honeycombed vertical surfaces, protecting exposed reinforcement, reinstating damaged arrises and repairing damaged precast concrete building units.
- Bedding Applications
Nitomortar BC is designed for bedding applications and can be trowelled to a fine accurate surface. Applications include bedding concrete kerbs to concrete, bedding bridge bearing pads and mounting heavy plant and equipment.
- Underwater Application
Nitomortar UA is formulated for use in exceptionally wet conditions and underwater applications. Nitomortar UA is recommended for reinstating structures exposed to the heavy battery of the sea (e.g.: sea walls) for repairing submerged steelwork or concrete (particularly exposed reinforcement) and for fixing slip bricks, tiles and tiles pointings.
Advantages
· High compressive strengths
· Fast cure
· No shrinkage on curing
· Excellent resistance to chemical physical attack
Coverage
Nitomortar : 1 ltr/m2 per mm thick
Properties
Setting time : 30 to 45 minutes at 20 C
Cure time Initial cure : 24 hrs. at 20 C
Final cure : 7 days at 20 C
Shrinkage on cure : None
Water immersion : Nitomortar UA may be applied underwater.
Compressive strength: After 1 week at 25-27 C
Nitomortar UA : 70 N/mm²
Flexural strength After 1 week at 25-27 C
Nitomortar UA : 35 N/mm²
Tensile strength : After 1 week at 25-27 C
Nitomortar UA : 12 N/mm²